The TE0320 is an industrial-grade FPGA micromodule integrating a leading-edge Xilinx Spartan-3A DSP FPGA, a USB 2.0 microcontroller, 32-bit wide 128 MByte DDR RAM, 4 MByte Flash memory for configuration and operation, and powerful switch-mode power supplys for all on-board voltages. A large number of configurable I/Os is provided via robust board-to-board (B2B) connectors.

All this on a tiny footprint, smaller than a credit card, at the most competitive price. Hardware and software development environment as well as reference designs are available.

Key Features

• Industrial-grade Xilinx Spartan-3A DSP FPGA module (1800 k gates or 3400 k gates)
• USB 2.0 (Hi-Speed USB) interface with a signaling bit rate of up to 480 Mb/s
• 32-bit wide 1 Gbit DDR SDRAM
• FPGA configuration through
  • B2B connector
  • JTAG port
  • SPI Flash memory
• Large SPI Flash memory for configuration and operation accessible through
  • B2B connector (SPI direct)
  • FPGA
  • JTAG port (SPI indirect)
  • USB bus (Firmware Upgrade Tool)
• 3 on-board high-power, high-efficiency, switch-mode DC-DC converters, capable of 3A each
• Power supply range: 4.0 V - 7.0 V
• Power supply via USB or B2B (carrier board)
• 4 LEDs, 2 push buttons, 8 DIP switches
• Plug-on module with 2 female header connectors
• 109 I/Os (+ 10 dual-purpose pins) available on B2B connectors
• Evenly spread supply pins for good signal integrity
• Cost optimized assembling variants to customer specification available

Specification

• FPGA: Xilinx Spartan-3A DSP:
  • XC3SD1800A-4FGG676C
  • XC3SD3400A-4FGG676C
• Cypress CY7C68013A-56LFXC EZ-USB FX2LP™:
  USB microcontroller, high speed USB peripheral controller
• Numonyx M25P16 / M25P32 / M25P64 / M25P128:
  32-Mbit, low voltage, serial Flash memory with 75 MHz SPI bus interface
• 2 × Micron Technology MT46V32M16BN-6:
  32-bit wide 512 Mbit DDR SDRAM component
• Microchip Technology 24LC128I-ST
  128 Kbit I2C CMOS serial EEPROM
• 3 × STMicroelectronics ST1S10:
  3 A, 900 kHz, monolithic synchronous step-down regulator
  3 A for each power rail: 1.2 V, 2.5 V, 3.3 V
• 2 × board-to-board (B2B) connectors:
  1.27 mm (50 mil) pitch 80-pin double row multi-pole socket (female) connectors
• 6-pin JTAG header
• 1 × USB mini B receptacle (device)
• 1 x LED (system)
• 4 × LED (user)
• 2 × push button (user)
• 4 x DIP switches (system)
• 8 × DIP switch (user)
• 1 x slide switch (system)

Dimensions

• Footprint: 68.0 mm x 48.0 mm
• Minimum height: 6 mm
• Mating height: 7 mm

Xilinx ISE Device Support

• Xilinx Spartan-3A DSP 1800: ISE WebPACK (completely free)
• Xilinx Spartan-3A DSP 3400: ISE Design Suite (license needed)