Key Features

• Industrial-grade Xilinx Spartan-6 LX FPGA micro-module (45/75/100/150)
• mini-USB 2.0 high-speed device (for configuration and operation)
• 16-bit-wide 1 Gb (128 MB) DDR3 SDRAM
• 64 Mbit (8 Mbyte) SPI Flash memory (for configuration and operation) accessible through:

  • FPGA
  • JTAG port (SPI indirect)
  • USB

• FPGA configuration through:

  • B2B connector
  • JTAG port
  • SPI Flash memory

• Plug-on module with 2 × 80-pin stacking connectors
• Up to 40 differential and up to 109 single-ended FPGA I/O pins available on B2B connectors
• 1.2 V, 1.5 V, 2.5 V = VCCAUX and 3.3 V power rails
• 24 MHz and 100 MHz reference clock signals
• eFUSE bit-stream encryption (LX75 or larger)
• 4 user LEDs
• 1 user push-button
• 2 user DIP switches
• Evenly-spread supply pins for good signal integrity
• Other assembly options for cost or performance optimization available upon request

Specifications

• Xilinx Spartan-6 LX FPGA:

  • XC6SLX45-2CSG484C = 43 k logic cells, commercial grade
    XC6SLX45-2CSG484I = 43 k logic cells, industrial grade
  • XC6SLX75-2CSG484C = 74 k logic cells, commercial grade
    XC6SLX75-2CSG484I = 74 k logic cells, industrial grade
  • XC6SLX100-2CSG484C = 101 k logic cells, commercial grade
    XC6SLX100-2CSG484I = 101 k logic cells, industrial grade
  • XC6SLX150-2CSG484C = 147 k logic cells, commercial grade
    XC6SLX150-2CSG484I = 147 k logic cells, industrial grade

• Cypress CY7C68013A-56LFXC EZ-USB FX2LP™:
  USB microcontroller, high speed USB peripheral controller
• 16-bit-wide (data-bus) 1 gigabit (128 megabyte) DDR3 SDRAM
• 64 megabit (8 megabyte) serial Flash memory with dual/quad SPI interface
• 2 x fine-pitch (0.5 mm) 80-pin board-to-board connectors
  Hirose DF17 series
• Up to 40 differential FPGA input/output pins available on B2B connectors
• Up to 109 single-ended FPGA input/output pins available on B2B connectors
• USB and JTAG pins available on B2B connectors
• 3.0 A high-efficiency DC-DC switching regulator for power rail 1.2 V
• 1.0 A high-efficiency DC-DC switching regulator for power rail 1.5 V
• 0.8 A DC-DC linear regulator for power rails 2.5 V and VCCAUX
• 3.0 A high-efficiency DC-DC switching regulator for power rail 3.3 V
• Power supervisory circuits with power-fail
• Power supply voltage range: 4.0 to 5.5 V
• Power supply source: USB port, board-to-board interconnect (e.g. carrier board)
• Dimensions: 47,5 × 40.5 mm (19.2 cm²)
• Minimum height: TBD (without connectors)
• Minimum height on carrier board: TBD
• Weight: 14.0 to 14.5 g
• Temperature grades:

  • commercial (C-type FPGA device)
  • industrial (I-type FPGA device)

Recommended Hardware

• Trenz Electronic TE0303 carrier board
  or
  Trenz Electronic TE0304 demo board
• JTAG programming cable

Recommended Software

• Trenz Electronic TE0630 LX45: Xilinx ISE WebPACK (free license)
• Trenz Electronic TE0630 LX75: Xilinx ISE WebPACK (free license)
• Trenz Electronic TE0630 LX100: Xilinx ISE Design Suite (you need to buy a license)
• Trenz Electronic TE0630 LX150: Xilinx ISE Design Suite (you need to buy a license)
• To use Trenz Electronic reference designs, you need one of the following Xilinx software licenses:

  • Xilinx WebPACK + EDK (Embedded Development Kit) stand-alone (TE0630 LX45 and LX75 only)
  • Xilinx ISE Design Suite - Embedded Edition
  • Xilinx ISE Design Suite - System Edition

You can find all Xilinx ISE versions here.

References

• manufacturer name: Trenz Electronic GmbH
• manufacturer part name(s) = manufacturer part code(s)

  • TE0630 XC6SLX45-2CSG484C = TE0630-00

• manufacturer part page: this page
• documentation archive: TDB